Remote start system with 2-way remotes with factory bypass module and 2 heated seats
Overview: The Viper Model 4816V 2-way Remote Start and Keyless Entry system can start your car and run it by remote control from a distance of up to 1 mile for a preset amount of time. The Model 4816V does not provide car security.
Note: The remote start function is for fuel injected, diesel, or hybrid vehicles only.
Remotes: The Model 4816V includes a 1-button transmitter (7816V) with 2-way operation, and a 1-button transmitter (7616V) with 1-way operation. The 2-way remote receives feedback from the control module and emits confirmation tones if the command is performed. If the feature cannot activated, or if the system is out of range, the 2-way remote emits a fault tone. The 7816V 2-way remote is powered by two CR2016 batteries (installed), while the 7616V 1-way remote has one CR2016 battery installed. Both 1-button remotes offer the following commands:
|System State||Press / Release||Press / Hold (3 sec)|
|Engine Off||Start engine||Car finder|
|Engine On||Unlock doors||Stop engine|
Car Finder: If you're having difficulty finding your vehicle in a crowded parking lot, the car finder function will cause the horn to emit one long honk (if connected) and the parking lights to flash for 10 seconds, to help you to locate your vehicle.
Rapid Resume Logic: This Viper remote start system stores its current settings in non-volatile memory. If power is lost while the unit is in the locked mode, the system will maintain locked mode and recall the stored settings from memory when power is restored.
Remote Starter Features
Remote Starting: Pressing and releasing the Remote Start button on the remote will remotely start the vehicle and run it for 12 minutes. You can extend the run time to 24 or 60 minutes. If you wish to pre-heat or pre-cool the vehicle, you must preset the climate controls prior to starting the vehicle. When you are ready to drive the remotely-started vehicle, insert the ignition key, turn it to the On position (not Start), and press the brake pedal.
Crank Time: If the unit is programmed for no engine checking or voltage sense, the crank time must be set to the appropriate duration. The default setting is 0.6 seconds. It can be lengthened to 0.8, 1.0, 1.2, 1.4, 1.6, 1.8, 2.0, or 4.0 seconds.
Diesel Start Delay: If you have a diesel vehicle, you can set the starter to delay by a few seconds before engaging. The Diesel Start Delay duration can be set to 15, 30, or 45 seconds. Gasoline engines will start approximately 4 seconds after the system acknowledges the start command by flashing the parking lights.
Turbo Timer: When the Turbo Timer mode is activated, the system keeps the engine running at idle for the Turbo Timer runtime (default 1 minute). This allows enough time to properly cool the turbo before turning it off.
Note: Turbo Timer mode must be turned on manually, and an optional activation switch must be installed on one of the included harnesses.
Pit Stop: This feature allows the vehicle to remain running after the key has been removed from the ignition. This is useful for those occasions when you wish to exit and lock the vehicle for short periods of time while leaving the motor running and the climate controls on.
Automatic Shut-down/Starter Lockout: After the vehicle is remote-started, the remote starter will shut down when the brake pedal is pressed, the hood is opened, if the run time expires, or when the remote start command is sent again from a remote control. In addition, if the hood is opened or if the brake pedal is pressed, you cannot start the vehicle using the remote starter.
Anti-grind Circuitry: Whenever the vehicle is started using the remote, advanced anti-grind circuitry prevents the starter from being engaged using the key. (In other words, it won't let you try to start the car with the key if the remote starter has already been engaged.) This prevents damage to the starter motor. The optional Failsafe Starter Kill relay must be installed in order for the anti-grind circuitry to work.
Directed DB3 Databus All Interface Module
Connects a security/remote start system to your vehicle's databus
- remote start/security integration module
- requires splicing into vehicle's factory wiring (generally 2-6 connections)
- allows easier interface with over 3000 different vehicles
(2) Echomaster PHSK-2L 1K Carbon fiber seat heater kit
- Set for two seat
- Very fast and homogeneous heating
- Heating elements adaptable to seat geometry
- Two heat levels switchable ( High / Low )
- Control via switch
- Integrated overheating protection
- Designed for installation in the seat upholstery
*Some vehicles may require extra parts. These items do not come with wiring diagrams or installation instructions. We recommend professional installation.